Trail Safe FJ80 Knuckle Ball Wiper Seals
Trail-Safe™ FJ80 Knuckle Ball Wiper Seal Kit
The Trail-Safe™ Knuckle Ball Wiper Seal is a double sided seal that keeps grease in and dirt out, all while eliminating the use of the OEM felt and rubber. Since it is made from seal-grade polyurethane, not UHMW, the seal is pliable enough to stretch over the knuckle ball during installation. This eliminates the need to cut the seal for installation which allows water to enter the knuckle ball and for grease to escape.
Trail-Safe™ Knuckle Ball Wiper Seals are without a doubt the best in the industry. No other design is comparable in performance and quality.
Note:. Trail-Safe™ Knuckle Ball Wiper Seals are sold in pairs and one kit will complete one front axle.
WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov
- Primary and secondary rod seal to insure that fluid leakage would never be an issue
- Two wiper seal design
- Triple Lip Piston Seal for consistent steering with no drift or fluid bypassing the piston
- The bushing allows the rod to absorb much higher side loads
- 4340 chromoly steel piston shaft
- Our Double Ended Ram have a 6", 8", or 10" stroke x 2.25" bore x 1.125” rod
- The cylinder has a black zinc-plate finish while the rod has 3/4x16 female threads on each end and is made entirely out of 4340 chromoly material
- The 6 inch ram and clevis kit has 6 total inches of travel and is perfect for Toyota's and narrowed Dana 44's.
- The 8 inch ram and clevis kit has 8 total inches of travel and was made to work with Dana 44's and custom length Dana 60 applications.
- The 10 inch ram and clevis kit has 10 total inches of travel and is used for buggies and comp rigs with up to 45 degree steering radius.
- 1,650 PSI of pressure at 4.5 gallons per minute
- 6, 8", or 10"" Double Ended Ram and Clevis Kit
- Orbital (100ml, 125ml, or 160ml)
- Full Hydraulic Steering Pump with Pulley
- Tie Rod Kit
- Double Ended Ram Mounting Kit
- Steering Column
- Orbital Mounting Kit
- Reservoir with Filter
- Reservoir Bracket
- Power steering belt
- Complete hose kit
- All necessary hardware
- 1990-1997 Toyota Land Cruiser FJ80
- 1995-1997 Lexus LX 450
All products carry our 12 Month Limited Warranty. All warranties are limited to the original purchaser and are not transferable to subsequent owners of the product. The warranty period begins on the purchase date. Trail-Gear warrants that it will repair or replace, free of charge, any eligible product which, under normal conditions of use and service, proves to be defective in materials or workmanship. This warranty does not cover any labor costs incurred in diagnosis of defects, removal or reinstallation of a product, nor does it cover any other consequential expenses.
Please read and review our return and warranty requirement document before sending in products.
Trail-Gear Inc. warranty does not cover, and Trail-Gear Inc. shall not be liable for, any undertaking, representation, or agreements made by dealers or other third parties selling Trail-Gear products, except where such agreements are within the provisions of this Warranty.
Specifically excluded from this warranty are failures caused by lack of maintenance, misuse, negligence, modification, abuse, improper application, crash damage, installation or operation, or failures caused by unauthorized service or use of unauthorized parts.
Additionally excluded from this warranty are parts which are subject to normal wear and tear, such as bushings, fluids, hoses, gaskets, belts, etc. Products not manufactured by Trail-Gear Inc. are excluded from any warranty and shall be handled with the original manufacturer.
All parts used in a competitive racing environment are excluded from this warranty. If, after inspection, a part returned, under any warranty, is deemed to be ineligible for warranty repair or replacement, the part may be repaired or replaced for a discounted cost. Return shipping charges will apply. Any part for which a warranty replacement is sought must be returned to Trail-Gear Inc. before any replacement items can be shipped. All replacement parts shipped before the suspect part has been received and evaluated by Trail-Gear, MUST BE PAID IN FULL. In such a case, after the suspect part has been received and approved for a warranty replacement, the purchase price for the replacement will be refunded.
- Please contact Trail-Gear Inc. at 559-252-4950 or email firstname.lastname@example.org prior to returning any product under warranty to verify that warranty is still in effect.
- Products must be shipped back to Trail-Gear Inc. at the expense of the customer.
- ATTN: WARRANTY
- 5356 E. Pine Avenue
- Fresno, Ca 93727.
Ship all products to:
- Please place a clearly marked copy of the original invoice on the outside of the package.
- Please include a short note stating the problem you are experiencing.
If any of the above mentioned policy is not met, the package will be refused or warranty claim denied. By completing the steps above, this will ensure faster processing of your claim so that Trail-Gear can get your product back to you as quickly as possible. All warranties are generally processed within 2-3 business days of Trail-Gear receiving the parts from you. Additional delays may be incurred if product needs additional testing or repairing.
If you are an international customer, please email the warranty department at email@example.com to receive further instruction. International customers may have the option to field destroy an approved warranty to avoid costly return shipping. In this case, any shipping charges for replacement parts will be at the expense of the customer.