Trail-Gear Performance 2.0-in Air Bump Set for 2nd Gen Tacoma with Modular Long Travel
Trail-Gear Performance 2.0-in Air Bump Set for 2nd Gen Tacoma with Modular Long Travel
If you’re running the All-Pro Modular Long Travel (MLT) Kit, you already know how capable your Tacoma is when wheeling, crawling, or tackling tough trails. But if you’re ready to push harder—charging through whoops, hitting higher speeds, or even catching air—your suspension is going to take a beating. While the MLT can handle the abuse, repeated bottom-outs can punish your shocks, suspension components, and even your back.
That’s why we specifically engineered the Trail-Gear Performance 2.0-in Air Bump Set for 2nd Gen Tacoma with Modular Long Travel for MLT-equipped Tacomas that need maximum control and protection when pushed to the limit.
This kit includes two weld-on brackets designed to mount directly to the MLT bulkhead, along with a pair of Trail-Gear 2.0” threaded-body bump stops featuring a 2” stroke. These bump stops are fully rebuildable, tunable, and lab-tested to over 1 million cycles. They’ve also been proven in real-world torture testing during the brutal King of the Hammers off-road endurance race.
By absorbing hard impacts at full suspension compression, Trail-Gear bump stops protect expensive shocks and suspension components from damage while delivering smoother handling and unmatched control. Tuning is simple—just adjust the nitrogen pressure through the Schrader valve to dial in the perfect setup for your driving style.
IMPORTANT:
- Welding required for installation.
- Bump stops are pre-charged to approximately 200 psi, which is a good starting point for most applications. To fine tune the bump stop you will need to release pressure through the Schrader valve or add pressure via a nitrogen fill kit (nitrogen fill kit not included). Refer to the Tacoma Modular Long Travel Kit instructions for specific guidance on tuning the Air Bumps for the MLT suspension.
- Caution: Charge only with Nitrogen gas. The use of compressed air or any other gas will cause damage to the internal components and void the warranty. Nitrogen gas is available for purchase at most welding supply shops.
WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov
- Fully Rebuildable Air Bump.
- 2” Diameter Zinc-Plated Steel Body
- 1-1/4” Hard-Chromed & Polished Shaft
- Ships pre-charged to 200psi this is a great starting point for tuning your suspension.
- Tunable by adjusting the nitrogen pressure and/or oil volume.
- Viton seals & O-rings.
- Threaded body with anodized aluminum locking rings allows quick & easy adjustment.
- O-Ring on shaft indicates amount of travel.
- Delrin contact pad for smooth & quiet operation.
- 2” stroke, 10-5/32” Extended, 8-5/32” Collapsed.
- Schrader valve with cap for quick & easy pressure adjustment.
- Bracket made from MIG-welded 3/16” thick ASTM A36 steel brackets & machined sleeve made from SAE 1020 DOM tubing.
- Welding required for installation.
- Includes spanner wrench.
| TOYOTA TACOMA - Prerunner/4WD Only (2005-2015) 2005 Toyota Tacoma 2006 Toyota Tacoma 2007 Toyota Tacoma 2008 Toyota Tacoma 2009 Toyota Tacoma 2010 Toyota Tacoma 2011 Toyota Tacoma 2012 Toyota Tacoma 2013 Toyota Tacoma 2014 Toyota Tacoma 2015 Toyota Tacoma |
Download installation instructions here.
Installation InstructionsAll products carry our 12 Month Limited Warranty. All warranties are limited to the original purchaser and are not transferable to subsequent owners of the product. The warranty period begins on the purchase date. Trail-Gear warrants that it will repair or replace, free of charge, any eligible product which, under normal conditions of use and service, proves to be defective in materials or workmanship. This warranty does not cover any labor costs incurred in diagnosis of defects, removal or reinstallation of a product, nor does it cover any other consequential expenses.
Please read and review our return and warranty requirement document before sending in products.
Warranty Exclusions
Trail-Gear Inc. warranty does not cover, and Trail-Gear Inc. shall not be liable for, any undertaking, representation, or agreements made by dealers or other third parties selling Trail-Gear products, except where such agreements are within the provisions of this Warranty.
Specifically excluded from this warranty are failures caused by lack of maintenance, misuse, negligence, modification, abuse, improper application, crash damage, installation or operation, or failures caused by unauthorized service or use of unauthorized parts.
Additionally excluded from this warranty are parts that are subject to normal wear and tear, such as bushings, fluids, hoses, gaskets, belts, etc. Products not manufactured by Trail-Gear Inc. are excluded from any warranty and shall be handled with the original manufacturer.
All parts used in a competitive racing environment are excluded from this warranty. If, after inspection, a part returned, under any warranty, is deemed to be ineligible for warranty repair or replacement, the part may be repaired or replaced for a discounted cost. Return shipping charges will apply. Any part for which a warranty replacement is sought must be returned to Trail-Gear Inc. before any replacement items can be shipped. All replacement parts shipped before the suspect part has been received and evaluated by Trail-Gear, MUST BE PAID IN FULL. In such a case, after the suspect part has been received and approved for a warranty replacement, the purchase price for the replacement will be refunded.
Axle/Birfield/CV Joint Warranty Disclaimer
Axle and Birfield/CV joints are warranted by the Trail-Gear Family of Companies for mechanical failures (e.g. breakage) only to the original purchaser. Proof of purchase is required for all warranty claims. Trail-Gear Family of Companies reserves the right to deny any claim if the product is shown to be incorrectly installed or the subject of collateral damage of surrounding components. Trail-Gear Family of Companies is not responsible for any collateral damages to any components caused by or related to a Trail-Gear Family of Companies product. Trail-Gear Family of Companies is not responsible for any shop/labor hours related to the installation or replacement of Trail-Gear Family of Companies product.
All warranty claims are subject to review and acceptance at the sole discretion of the Trail-Gear Family of Companies and may require the return of parts at the customer's expense for warranty review. Parts that are rejected for warranty coverage will be shipped back to the customer at the customer’s expense or scrapped after 10 business days.
For Axle and Birfield/CV joints with Lifetime Warranty, Lifetime Warranty means one-time replacement within the lifetime of originally purchased product only to the original purchaser.
The warranty does not cover the following conditions:
- Normal wear and tear
- Noise
- Twisted shafts
- Twisted splines
- Bent axles
- Stripped threads
- Modification of the product
- Intentional or willful destruction of the product
- Failures from improper installation or storage
- Failures from other than the intended use
- Please contact Trail-Gear Inc. at 559-252-4950 or email sales@trail-gear.com prior to returning any product under warranty to verify that warranty is still in effect.
- Products must be shipped back to Trail-Gear Inc. at the expense of the customer. Ship all products to:
- ATTN: WARRANTY
- 5356 E. Pine Avenue
- Fresno, CA 93727.
- Please place a clearly marked copy of the original invoice inside the package.
- Please include a short note stating the problem you are experiencing.
If any of the above mentioned policy is not met, the package will be refused or warranty claim denied. By completing the steps above, this will ensure faster processing of your claim so that Trail-Gear can get your product back to you as quickly as possible. All warranties are generally processed within 2-3 business days of Trail-Gear receiving the parts from you. Additional delays may be incurred if product needs additional testing or repairing.
If you are an international customer, please email the warranty department at sales@trail-gear.com to receive further instruction. International customers may have the option to field destroy an approved warranty to avoid costly return shipping. In this case, any shipping charges for replacement parts will be at the expense of the customer.
